Page 1 of 1
0G02 did not have permission 24/11/2019 at 21:09 #121901 | |
nroberts
![]() 227 posts |
Extract of message window: 03:33:34 7K91 has permission at Ferrybridge PS Controller 03:33:34 0G02 has permission at Knottingley TMD 03:33:43 6K81 arrived at Milford West Sidings 5 min(s) late 03:34:28 Point normalisation alarm for PF2120 03:34:44 6K81 has finished dividing 03:35:17 0G02 did not have permission (Knottingley TMD) At 3:33:34 I checked given permissions and had both 7K91 and 0G02 with permissions. 2 minutes later I'm informed 0G02 did not have permission.... :( Loader: v4.15.1 Timetable: West Yorkshire July 1991 - September 1991 Timetable Sim version: 2.3 Log in to reply |
0G02 did not have permission 25/11/2019 at 11:34 #121905 | |
58050
![]() 2652 posts |
nroberts in post 121901 said:Extract of message window: Log in to reply The following user said thank you: nroberts |
0G02 did not have permission 25/11/2019 at 18:02 #121924 | |
Bobby
![]() 22 posts |
I had the same problem today with 0A02.
Log in to reply |
0G02 did not have permission 25/11/2019 at 19:12 #121928 | |
Dick
![]() 387 posts |
Quite a while since I have played West Yorkshire, but I seem to recall I had the same problem with a number of locos at Knottingley TMD.
Log in to reply |
0G02 did not have permission 25/11/2019 at 21:27 #121931 | |
nroberts
![]() 227 posts |
Maybe there's something in the way that entry-points are defined whereby if the loco does not enter on the exact expected entry point it's considered non-authorized. However **this is clearly speculation** aimed at maybe giving ideas to the devs as to what may have caused it. Independently of this I find this an excellent simulation to enjoy (particularly if you try the "heavy freight" in the early morning with miriad loco and freight movements). Definitely one of the most interesting sims in terms of variety... Log in to reply |
0G02 did not have permission 26/11/2019 at 08:29 #121933 | |
vloris
![]() 37 posts |
Could you add a savegame, or explain where you tried to send 0G02? All loco's destined to Knottingley TMD should enter behind either signal FE5414 or FE5415. Most (if not all) of them need to reverse at England Lane LC (behind FE5424) to enter. If you route it straight in from Knottingley West Jn, you get the 'no permission' message. This thread: https://www.SimSig.co.uk/Forum/ThreadView/49657 also has an explanation about this. Log in to reply The following user said thank you: nroberts |
0G02 did not have permission 26/11/2019 at 08:42 #121935 | |
Bobby
![]() 22 posts |
vloris in post 121933 said:Could you add a savegame, or explain where you tried to send 0G02?This explains why I received the 'no permission' message. Log in to reply |
0G02 did not have permission 26/11/2019 at 16:27 #121938 | |
KymriskaDraken
![]() 963 posts |
58050 in post 121905 said:nroberts in post 121901 said:It's as others have said. You need to send the engine into the correct end of the shed. Almost everything goes in at the England Lane end.Extract of message window: Kev Log in to reply |
0G02 did not have permission 26/11/2019 at 18:05 #121940 | |
nroberts
![]() 227 posts |
vloris in post 121933 said:Could you add a savegame, or explain where you tried to send 0G02?Got it. That was the problem. As it did not mention reversing at England Lane I sent it straight in. Many thanks. Log in to reply |
0G02 did not have permission 26/11/2019 at 18:15 #121941 | |
headshot119
![]() 4869 posts |
Trains failing to phone wrong route at FE5398 has been reported on Mantis 28320
"Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply |