Page 1 of 1
| Bicester 25/09/2020 at 19:41 #132683 | |
ajax103
1120 posts |
The sim says there is a Bicester to Oxford panel but the sim doesn't show where the actual boundary is compared to the clear boundary between North/South/ LUL/South and Banbury/North so not sure if its been put on Mantis but could it please?
Log in to reply |
| Bicester 25/09/2020 at 20:07 #132686 | |
bill_gensheet
1413 posts |
Existing Mantis was that the Oxford branch area is on 'North' and that it is the duty box that should not be there. 17275 - shown as resolved in v3.7 Have added a note. Bill Last edited: 25/09/2020 at 20:09 by bill_gensheet Reason: None given Log in to reply The following user said thank you: ajax103 |
| Bicester 25/09/2020 at 20:33 #132687 | |
|
TUT
532 posts 
|
As Bill says there is currently no separate Bicester to Oxford panel, there are two workstations at Marylebone: North and South. Bicester to Oxford is on the north although it being scaleable IECC the south signaller is perfectly capable of scrolling over to, say, Oxford Parkway and setting a route from their seat on their monitors. However, the CCTV camera for the level crossing and the associated controls are only on the north workstation What the future will bring for the OXD when East West Rail finish only time will tell. It was due to go into Rugby ROC, but with the reorganisation and the devolution it's now the wrong section. There is talk of it going into Marylebone in which case one day there might well be a separate workstation in Marylebone covering Bicester to Oxford, but it will do a little bit more besides that. Log in to reply |
| Bicester 26/09/2020 at 08:57 #132693 | |
|
Stephen Fulcher
2078 posts |
It would be a tight fit to put another workstation in Marylebone IECC
Log in to reply |
| Bicester 26/09/2020 at 09:13 #132694 | |
|
ajax103
1120 posts |
Why not then remove the panel as it is on the simulation and have it come fully under the North signaller then?
Log in to reply |
| Bicester 26/09/2020 at 17:56 #132712 | |
|
Stephen Fulcher
2078 posts |
That’s why Bill reopened the bug report on Mantis
Log in to reply |
| Bicester 26/09/2020 at 18:03 #132715 | |
GeoffM
6376 posts |
Stephen Fulcher in post 132712 said:That’s why Bill reopened the bug report on MantisNo, he didn't. He added a note. You reopened it. In any case, there are several simulations with additional workstations so I'm leaving this flexibility in. SimSig Boss Log in to reply |
| Bicester 26/09/2020 at 19:43 #132721 | |
|
bill_gensheet
1413 posts |
I was not able to change the Mantis status to 'feedback' / '[new] question' or I would have. To close out for the OP and accepting there is no need to show the split on screen, might be worth adding something to the manual covering any behaviours when different players have North and Bicester - Oxford workstations in 2015/2016 eras. eg which workstation gets calls from which signals / crossings Log in to reply |
| Bicester 28/09/2020 at 14:35 #132772 | |
|
ajax103
1120 posts |
GeoffM in post 132715 said:Stephen Fulcher in post 132712 said:Pardon for asking but if you're hosting the simulation for example and I take the Oxford to Bicester panel then why do the calls still go to the South Panel?That’s why Bill reopened the bug report on MantisNo, he didn't. He added a note. You reopened it. In any case, there are several simulations with additional workstations so I'm leaving this flexibility in. I can understand if the former panel hasn't been taken but not if it has. Would it be possible for calls and slot requests to go to the Oxford to Bicester panel when it's been taken in MP mode at all? No idea how much coding would be needed? Log in to reply |