Page 1 of 1
Exeter Junction 18/10/2012 at 12:15 #36643 | |
Class41
![]() 3 posts |
As a relatively new operator of SimSig, I'm having a problem with reversing 5E06 at Exeter central at around 08:20 in the 2006 timetable v 2.222 with Exeter v2.227.0. It would appear that the unit should go into the yard, wait for three mainline moves before setting off towards central. The timetable shows the train as a down move before it has crossed over, I wonder if this is what causes the confusion? I've tried all the suggestions offered in both the previous threads I've found on this subject, but to no avail. I am an experienced railman of 44 yrs. and know the Exeter area well, having worked out of the depot for many years. Has anyone come up with a solution to this apparent problem, as I have come to a grinding halt on this move. Many thanks, Steve M Log in to reply |
Exeter Junction 18/10/2012 at 18:18 #36657 | |
BarryM
![]() 2158 posts |
Reverse the train at sig. EJ7 (On branch to CE Works). Barry Barry, Sydney, New South Wales, Australia Last edited: 18/10/2012 at 18:24 by BarryM Log in to reply |
Exeter Junction 18/10/2012 at 18:36 #36658 | |
Josie
![]() 310 posts |
" said:Reverse the train at sig. EJ7 (On branch to CE Works).That's the right reversing location, but how do you get the timetable to validate? I've been playing around with it this afternoon to try and make it work, and it keeps saying there are no valid paths. It looks to me like it ought to be:
But the train just "runs out of valid track" and the timetable editor claims there's no route from Rev Exmouth Jn East to Exmouth Jn. Log in to reply |
Exeter Junction 18/10/2012 at 18:41 #36659 | |
AndyG
![]() 1842 posts |
" said:Try Rev Exmouth Jn East - Exeter Central (ie omit Exmouth Jn). I can only help one person a day. Today's not your day. Tomorrow doesn't look too good either. Log in to reply |
Exeter Junction 18/10/2012 at 18:55 #36660 | |
John
![]() 884 posts |
Reverse on Up W'loo [E750] instead of Exmouth Jcn. Job done. Log in to reply |
Exeter Junction 18/10/2012 at 19:02 #36661 | |
Josie
![]() 310 posts |
" said:Reverse on Up W'loo [E750] instead of Exmouth Jcn.Job only done if no other trains need to pass while your train is reversing! " said: Try Rev Exmouth Jn East - Exeter Central (ie omit Exmouth Jn).Andy's got it, as always. Leave out Exmouth Jn (in both directions) and it validates fine. So to the OP, you need to edit the timetable and change Exmouth Jn to Rev Exmouth Jn East - and all should be well. Log in to reply |
Exeter Junction 18/10/2012 at 19:04 #36662 | |
BarryM
![]() 2158 posts |
" said:Reverse on Up W'loo [E750] instead of Exmouth Jcn.Unfortunately not as 5E06 needs to be off the main lines for other trains to cross before proceeding to Exeter. Barry Barry, Sydney, New South Wales, Australia Log in to reply |
Exeter Junction 18/10/2012 at 19:24 #36663 | |
AndyG
![]() 1842 posts |
" said:
The logic behind it is that junction locations are at the last signal BEFORE the junction, not the actual junction itself. Hence a train at Ex Jn (rev) won't actually pass the Ex Jn location on the running line from Pinhoe. In the other direction it's probably due to the paths provided and the associated key locations. Although Ex Jn is a key location for the main running routes paths, it's not included in the shunt routes, these being to/from Ex Jn (rev) directly. I can only help one person a day. Today's not your day. Tomorrow doesn't look too good either. Last edited: 18/10/2012 at 19:33 by AndyG Log in to reply |
Exeter Junction 18/10/2012 at 22:39 #36667 | |
Class41
![]() 3 posts |
Many thanks for all the replies - I'm glad I'm not the only confused one on this. I managed to go the way Barry suggested, up the Exmouth after reversing at the LOS, then again reversing back towards Central, caused loads of delay, and not very prototypical, but it worked. SteveM Log in to reply |
Exeter Junction 18/10/2012 at 23:14 #36668 | |
Class41
![]() 3 posts |
Thanks AndyG, that did the trick. SteveM Log in to reply |
Exeter Junction 18/01/2014 at 20:59 #54008 | |
DaveHarries
![]() 1280 posts ![]() |
Sorry to rejuvenate this topic but I wish to clear two things up: 1. Is "Exmouth Junction East" the HS siding opp. the CE works? 2. I see that the HS siding is, by the looks of things, uncircuited. So if, for example, I put train 5X00 into the HS siding at Exmouth Junction does the train exit the sim (meaning I would need to create a separate train, ie. 5X002, for anything to come back out of HS) or can I just do it as a reverse and have the whole lot on the 5X00 TT? Cheers, Dave Last edited: 18/01/2014 at 21:03 by DaveHarries Log in to reply |
Exeter Junction 18/01/2014 at 21:14 #54010 | |
Peter Bennet
![]() 5377 posts |
" said:Sorry to rejuvenate this topic but I wish to clear two things up: Yes and at EJ20 " said: HS is 200m long and a single siding- so no fall-off, trains at the CE will fall-off. Peter I identify as half man half biscuit - crumbs! Last edited: 18/01/2014 at 21:14 by Peter Bennet Log in to reply The following user said thank you: DaveHarries |
Exeter Junction 18/01/2014 at 21:20 #54011 | |
Steamer
![]() 3958 posts |
" said:Sorry to rejuvenate this topic but I wish to clear two things up:1. Yes 2. It's just a siding, there's no exit point. The way it's displayed is a bit unusual- most non-entry point sidings have a grey vertical bar at the end of them. "Don't stress/ relax/ let life roll off your backs./ Except for death and paying taxes/ everything in life.../ is only for now." (Avenue Q) Log in to reply |