Page 1 of 2
| Valley wrong route 19/01/2013 at 18:19 #40699 | |
peterb
452 posts |
See picture - as 1G40 left HHD, I set the next location to be the Britannia Bridge. At Valley, it gave an 'incorrect route set' warning.
Post has attachments. Log in to view them. Log in to reply |
| Valley wrong route 19/01/2013 at 18:47 #40700 | |
|
Stephen Fulcher
2078 posts |
It looks like the sim is still expecting to see the compulsory timing points of Valley and Gaerwen. If you tell the driver to accept the route you will get around the issue, which appears to be with the route checking contained within the sim code expecting that route to "see" Gaerwen in the trains timetable. As he is no longer booked to pass there, he will call wrong route. I will forward it onto Karl. Last edited: 19/01/2013 at 18:55 by Stephen Fulcher Log in to reply |
| Valley wrong route 19/01/2013 at 18:55 #40701 | |
onlydjw
456 posts |
Location checking will only work with a TT with valid paths. If you don't have a valid TT, then you may get wrong route calls, because the TT is invalid.
God bless, Daniel Wilson Log in to reply |
| Valley wrong route 19/01/2013 at 22:59 #40705 | |
|
Josie
310 posts |
If this is deliberate behaviour it's a change from other sims, where setting current/next location to somewhere distant will leave the train happily rattling on in any direction until it picks up the timetable again. A good example is on King's Cross, if (e.g.) the Hertford Loop is blocked you can tell a train at Langley that its current/next location is Alexandra Palace and it'll happily take any route via WGC until it can pick up its booked timetable at Ally Pally.
Log in to reply |
| Valley wrong route 20/01/2013 at 04:04 #40707 | |
BarryM
2158 posts |
" said:If this is deliberate behaviour it's a change from other sims, where setting current/next location to somewhere distant will leave the train happily rattling on in any direction until it picks up the timetable again. A good example is on King's Cross, if (e.g.) the Hertford Loop is blocked you can tell a train at Langley that its current/next location is Alexandra Palace and it'll happily take any route via WGC until it can pick up its booked timetable at Ally Pally.Josie, North Wales Coast is an entirely different signalling system compared with Kings Cross. Barry Barry, Sydney, New South Wales, Australia Log in to reply |
| Valley wrong route 20/01/2013 at 04:48 #40708 | |
|
BarryM
2158 posts |
" said:See picture - as 1G40 left HHD, I set the next location to be the Britannia Bridge. At Valley, it gave an 'incorrect route set' warning.Why did you set the next location as Britannia Bridge? The next location is Amwlch. Why did you want to change the trains location at all? The TT is set correctly with all timing locations shown. Setting the trains location from Valley to Britannia Bridge will definitely bring up the warning as Gaerwen is in between. Barry Barry, Sydney, New South Wales, Australia Log in to reply |
| Valley wrong route 20/01/2013 at 13:50 #40715 | |
|
peterb
452 posts |
Barry, Just to clarify, regarding 'signalling system' are you referring to the core code or system in place on the ground (i.e. AB/TCB)? If the latter then I would have still expected the sim to have behaved in the manner which Josie describes, especially since in this instance there are no diverging routes between the two locations, hence this bug report. Had there not been a junction on the up line at VAL I doubt the sim would have brought up the warning. By setting the next location as Britannia Bridge on departure from HHD, my intention was to run the train non-stop to Bangor due to delay, as it was timetabled to all-stop. Thanks. Log in to reply |
| Valley wrong route 20/01/2013 at 13:56 #40716 | |
headshot119
4869 posts |
The issue is that the route checking at that signal is expecting to find Gaerwen in the trains timetable, as that is the next compulsory timing point, if you had set the next location as Gaerwen the train wouldn't phone in wrong route. For the purposes of route checking there is a diverging junction between the two, it is at the signal which the train is calling in wrong route. "Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply |
| Valley wrong route 20/01/2013 at 14:01 #40717 | |
|
Ben86
126 posts |
" said:It sounds like there are some key locations you have skipped over by setting the next location to Britannia Brdige. A solution might be to tick the 'passing time' option for each of the scheduled station calls, if you want the train to run non-stop. Log in to reply |
| Valley wrong route 21/01/2013 at 12:45 #40744 | |
|
clive
2789 posts |
" said:The issue is that the route checking at that signal is expecting to find Gaerwen in the trains timetable, as that is the next compulsory timing point, if you had set the next location as Gaerwen the train wouldn't phone in wrong route.The core code allows the developer to say, for each route: - wrong route if X appears in the timetable - wrong route if X does not appear in the timetable - wrong route if X is not the next location in the timetable There's also a facility for custom tests, but those are more work to write so the above three are the most common. Most sim developers use the first one in most situations, reserving the other two for special cases like sidings. It would appear that NWC has been written differently, and this is a side-effect of doing that. Log in to reply The following user said thank you: Josie |
| Valley wrong route 21/01/2013 at 19:09 #40756 | |
|
headshot119
4869 posts |
" said:" said:I'm aware of the options that are available.The issue is that the route checking at that signal is expecting to find Gaerwen in the trains timetable, as that is the next compulsory timing point, if you had set the next location as Gaerwen the train wouldn't phone in wrong route.The core code allows the developer to say, for each route: I've adjusted the sim to eliminate the error, but if trains where running as they should be things like this wouldn't occur. "Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply |
| Valley wrong route 21/01/2013 at 19:28 #40757 | |
postal
5264 posts 
|
" said:. . . . if trains where running as they should be things like this wouldn't occur.Just like the real railway, then. “In life, there is always someone out there, who won’t like you, for whatever reason, don’t let the insecurities in their lives affect yours.” – Rashida Rowe Log in to reply The following user said thank you: headshot119 |
| Valley wrong route 21/01/2013 at 19:43 #40758 | |
|
Josie
310 posts |
" said:I'm aware of the options that are available.I wasn't though - thanks Clive. " said: I've adjusted the sim to eliminate the error, but if trains where running as they should be things like this wouldn't occur.But of course they don't always! Another example I saw this afternoon; I had a 5Cxx train heading to Hornsey EMU Depot which, because of a series(!) of awkward failures, had got stuck on the Down Fast. I abandoned the timetable, sent it to Bowes Park to reverse, then reinstated its timetable with 'current/next location' set to Harringay Rev Sdg. In this case it was completely off its booked route, but it cleared all junctions etc. without comment until it arrived at a place it was expecting. I realise it's not a feature as such, but it's a useful option to have rather than having to write a full emergency timetable if there's disruption to a single train. Log in to reply |
| Valley wrong route 21/01/2013 at 19:48 #40759 | |
Peter Bennet
5402 posts |
It is possible to add bespoke code to automatically jump the timetable in cases of diversion. CScot has it in abundance. However, bespoke coding is being phased out so the feature may not be available in future Sims. Peter I identify as half man half biscuit - crumbs! Log in to reply |
| Valley wrong route 21/01/2013 at 23:34 #40779 | |
|
Danny252
1461 posts |
" said:It is possible to add bespoke code to automatically jump the timetable in cases of diversion. CScot has it in abundance. However, bespoke coding is being phased out so the feature may not be available in future Sims.Really? The more recent sims seem to be drowning in bespoke features - Euston, NWC, CScot, NEScot, and so on. Have they just been a bit too much hassle when testing/coding? Log in to reply |
| Valley wrong route 22/01/2013 at 11:20 #40786 | |
|
headshot119
4869 posts |
" said:" said:Peter is referring to "custom code" rather than code we can achieve in the sim data.It is possible to add bespoke code to automatically jump the timetable in cases of diversion. CScot has it in abundance. However, bespoke coding is being phased out so the feature may not be available in future Sims.Really? The more recent sims seem to be drowning in bespoke features - Euston, NWC, CScot, NEScot, and so on. Have they just been a bit too much hassle when testing/coding? I can't speak for other sims, but NWC uses no "custom code" at all to achieve any of the bespoke features. The AB controls are essentially a set of logic flags connected to a set of slots. Once one was made and tested, and we were happy with it, I copied it across the sim. I can't think of the top of my head what other bespoke features NWC has, but I'm happy to explain any of the others to you. "Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply |
| Valley wrong route 22/01/2013 at 12:59 #40787 | |
jc92
3685 posts
|
" said:" said:the only recent custom code i can think of (assuming it is custom and not actually a full new feature) is the capacity control on euston/WemSub.It is possible to add bespoke code to automatically jump the timetable in cases of diversion. CScot has it in abundance. However, bespoke coding is being phased out so the feature may not be available in future Sims.Really? The more recent sims seem to be drowning in bespoke features - Euston, NWC, CScot, NEScot, and so on. Have they just been a bit too much hassle when testing/coding? "We don't stop camborne wednesdays" Log in to reply |
| Valley wrong route 22/01/2013 at 13:08 #40788 | |
|
headshot119
4869 posts |
" said:" said:" said:the only recent custom code i can think of (It is possible to add bespoke code to automatically jump the timetable in cases of diversion. CScot has it in abundance. However, bespoke coding is being phased out so the feature may not be available in future Sims.Really? The more recent sims seem to be drowning in bespoke features - Euston, NWC, CScot, NEScot, and so on. Have they just been a bit too much hassle when testing/coding? "Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply |
| Valley wrong route 22/01/2013 at 13:36 #40789 | |
|
peterb
452 posts |
Just to also add this one. See no reason why this shouldn't somehow be allowed (5D82 is for the CS)
Post has attachments. Log in to view them. Log in to reply |
| Valley wrong route 22/01/2013 at 13:42 #40790 | |
|
headshot119
4869 posts |
" said:Just to also add this one. See no reason why this shouldn't somehow be allowed (5D82 is for the CS)That one has been reported to me previously, that's been fixed in the next version. "Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply |
| Valley wrong route 22/01/2013 at 13:54 #40791 | |
|
peterb
452 posts |
Also, please can you just check where the sim thinks TC TAE3 is? I had a TCF and it came up as being in the Llanrwst area... (and yes I'm sure it was that TCF!)
Log in to reply |
| Valley wrong route 22/01/2013 at 14:24 #40792 | |
|
headshot119
4869 posts |
" said:Also, please can you just check where the sim thinks TC TAE3 is? I had a TCF and it came up as being in the Llanrwst area... (and yes I'm sure it was that TCF!)See this thread. "Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply |
| Valley wrong route 22/01/2013 at 15:02 #40794 | |
|
clive
2789 posts |
" said:I've adjusted the sim to eliminate the error, but if trains where running as they should be things like this wouldn't occur.My experience is that you're better off using the "can't get there" options rather than "have to have X in the timetable" options. When things start going wrong, it means that trains only complain if they really can't cope with the route you've offered them. I also generally follow the principle of only putting a test in at the point where the train absolutely has to make a commitment. (None of this is criticism of how you've done it, just discussion points.) Log in to reply |
| Valley wrong route 22/01/2013 at 15:14 #40795 | |
|
clive
2789 posts |
" said:" said:Bespoke coding is a hassle when trying to debug problems that appear to be in the core code. But the main reason for getting rid of it are some future developments that I'm not at liberty to talk about.Really? The more recent sims seem to be drowning in bespoke features - Euston, NWC, CScot, NEScot, and so on. Have they just been a bit too much hassle when testing/coding? Euston had about four bits of custom code in it. I looked at it about a month ago for other reasons and found that all bar one of them could be replaced by core code features that have been added since then. That left the little lamp by the Up Carriage Sidings that shows if there's room for another train. I added a new core code feature that allowed that to be done (it's more generic than that, so will be useful for other sims). So when Euston gets refreshed it will not have any custom code. Log in to reply |
| Valley wrong route 22/01/2013 at 15:17 #40796 | |
|
clive
2789 posts |
" said:That was a core code feature from day one. Log in to reply |