Page 1 of 1
Rugeley Power Station 28/03/2014 at 22:57 #57966 | |
splash
102 posts |
I know other people are having problems with trains leaving the power station at Rugeley. So i did a test myself and added two trains to the timetable.One leaves at 00:05 to go through Hednesford, and the other leaves at 00:10 to go to Crewe. Data was taken from the timetable for the other trains. Both trains appeared at the time they were suppose to and ran to there destinations without any problems. May I thank everyone involved in updating Stafford and hope they can get trains to leave Rugeley Power Station again. i have done it so i hope it works for you all.
Log in to reply |
Rugeley Power Station 28/03/2014 at 23:43 #57974 | |
Airvan00
129 posts |
Thanks for doing that, I had thought of creating trains from scratch. As I thought the reason was some error in the timetable was causing trains not to enter. But in my case the yardmaster calls and I authorise the train to enter , but it never does. If a call is made surely the sim has started the processing of that train. But it appears to fail at that point.
Log in to reply |
Rugeley Power Station 28/03/2014 at 23:56 #57976 | |
splash
102 posts |
I still get the call that the train is ready to leave and enters at the starting signal. Then i set the route, clear the signal and let it run to its destination. THese were only test trains to see if there was a problem with putting timings into the timetable editor. I had no problems programming in the information and the trains ran ok.
Log in to reply |
Rugeley Power Station 29/03/2014 at 09:35 #57982 | |
Steamer
3984 posts |
" said:Thanks for doing that, I had thought of creating trains from scratch. As I thought the reason was some error in the timetable was causing trains not to enter. But in my case the yardmaster calls and I authorise the train to enter , but it never does. If a call is made surely the sim has started the processing of that train. But it appears to fail at that point.Have you clicked 'Check for Updates' in the Loader? A new version of Stafford was released yesterday. "Don't stress/ relax/ let life roll off your backs./ Except for death and paying taxes/ everything in life.../ is only for now." (Avenue Q) Log in to reply The following user said thank you: nroberts |
Rugeley Power Station 30/03/2014 at 07:14 #58013 | |
Airvan00
129 posts |
Even after the update still the same. Yardman calls, permission given. Train never enters. Never appears in the F 2 list, but looking at the timetable it is greyed out. Log in to reply |
Rugeley Power Station 17/04/2014 at 19:37 #59043 | |
LordSven
29 posts |
Hi all. Thanks for another great sim. I too am having problems with trains entering at Rugely B. P. S. Shunter calls with TRTS, I give permission to enter but the train never appears. System files and Sim files are fully up to date. Problem occurred since the refreshed sim was published, before and after update. I am running W7 Ultimate x64. Cheers!
Last edited: 17/04/2014 at 22:22 by LordSven Reason: Typo Log in to reply |
Rugeley Power Station 18/04/2014 at 00:15 #59050 | |
postal
5264 posts |
I think it is a problem in the TT with the rules and percentage probabilities as I have re-written the TT for my own purposes with the rules changed to "are alternatives" and the percentages taken out after which something enters every time there is a one of a batch due to enter. Rules are also needed to link the trains for the North going off sim at Hednesford to their equivalents entering at Bushbury. All discussed previously here.
“In life, there is always someone out there, who won’t like you, for whatever reason, don’t let the insecurities in their lives affect yours.” – Rashida Rowe Log in to reply The following user said thank you: LordSven |
Rugeley Power Station 18/04/2014 at 19:38 #59088 | |
LordSven
29 posts |
Thank you so much for the rapid reply!
Log in to reply |