Page 1 of 1
BN51 lamp failure 01/10/2014 at 16:15 #64807 | |
Dick
387 posts |
I have got the situation where there is a lamp failure at BN51 that is causing OL3150 to be held at red. 6o15 is stopped at OL3150, however, I can't talk him past as I don't control that signal. As far as the Sim goes, I suspect I will have to wait for S&T to change the bulb but how would this situation be dealt with in real life?
Log in to reply |
BN51 lamp failure 01/10/2014 at 17:07 #64810 | |
headshot119
4869 posts |
The signaller at Leamington would talk 6O15 past OL3150, he has track circuit indications upto and including the overlap of BN51 signal.
"Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply |
BN51 lamp failure 01/10/2014 at 18:01 #64813 | |
Danny252
1461 posts |
" said:The signaller at Leamington would talk 6O15 past OL3150, he has track circuit indications upto and including the overlap of BN51 signal.Though I would assume that the signaller at BN need to give him permission to do so (as it is entering a block section between two signalboxes, albeit one that is usually controlled without any direct input from either end), and also have the Leamington signaller caution the train with regards to the failure so that the driver doesn't suddenly find a dark signal. Last edited: 01/10/2014 at 18:02 by Danny252 Log in to reply |
BN51 lamp failure 01/10/2014 at 18:10 #64815 | |
Dick
387 posts |
Could this not be simulated in Simsig by having the ability to talk trains past signals not controlled by the Simsig signaller but impacting on running the sim. Just a thought.
Log in to reply |
BN51 lamp failure 01/10/2014 at 18:31 #64816 | |
headshot119
4869 posts |
" said:Could this not be simulated in Simsig by having the ability to talk trains past signals not controlled by the Simsig signaller but impacting on running the sim. Just a thought.If it's a single player game you can talk the train past using F2. If it's a multiplayer game the host can use F2 to do this. "Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply |
BN51 lamp failure 01/10/2014 at 20:53 #64820 | |
Dick
387 posts |
If it's a single player game you can talk the train past using F2. If it's a multiplayer game the host can use F2 to do this.[/quote] But you can't, that was the point of the post. The train is standing at a signal outside of the sim's control and can't be talked past. Log in to reply |
BN51 lamp failure 01/10/2014 at 21:20 #64823 | |
Steamer
3958 posts |
" said:" said:You can still tell it to go past using F2, right click the train> Signalling options> Authorise train to pass signal at danger.If it's a single player game you can talk the train past using F2. If it's a multiplayer game the host can use F2 to do this.But you can't, that was the point of the post. The train is standing at a signal outside of the sim's control and can't be talked past. "Don't stress/ relax/ let life roll off your backs./ Except for death and paying taxes/ everything in life.../ is only for now." (Avenue Q) Log in to reply |
BN51 lamp failure 01/10/2014 at 21:32 #64824 | |
Dick
387 posts |
No you can't, you get an error message.
Log in to reply |
BN51 lamp failure 01/10/2014 at 21:36 #64825 | |
Dick
387 posts |
Doh, how many years have I been playing Simsig and still enter 0 instead of o !!!! :doh :doh :doh
Log in to reply |