Page 1 of 1
| A couple of Derby based queries 28/03/2015 at 01:33 #70415 | |
pedroathome
915 posts 
|
Just a couple queries on Derby in relation to drawing of the sim. 1 - Slum Sdgs: The points in are shown as not having one direction or another without a route set over them, is this correct? 2 - Mosley Street GF: I am able to release the ground frame with a route set over, although the signal does revert to danger, this does not seem right 3 - Belper GF: I am unable to release the DM frame release without first releasing the one for the up main. This is understandable (Lever 1 then 4 in frame). If I then give back the king lever on on 1, lever 4 is then locked out of the frame, until the king lever is taken for 1. Should these be locked in such a way to prevent this, or is this as per reality? - After looking at the other similar frames on the sim, should these maybe be separate releases not looking into the state of the other? On a side note here, how do you get lever 5 to pull on this frame? 4 - Engine Sdgs No.1 GF: Should I be able to pull off both levers 7 and 9 at the same time? All of these looked at in the newest era. Other than these, I will happly say its a very enjoyable sim, that, I doubt later I will be saying comfortable for a single player James Log in to reply |
| A couple of Derby based queries 29/03/2015 at 11:25 #70484 | |
Stephen Fulcher
2078 posts
|
1. This is a bug but not the one you think - this is actually part of Engine Sidings No1 Ground Frame, which seems to behaving as though it was not. Mantis 12688. 2. This is a wrong side failure. Mantis 12689. 3. My gut instinct is that lever 4 should be replaced before the frame would allow lever 1 replaced (ie the reverse of pulling them). Lever 5 appears to be a bug. Mantis 12690. 4. Confused by this one as there are only 8 levers on the frame. Did you mean another number? Log in to reply |
| A couple of Derby based queries 29/03/2015 at 12:10 #70485 | |
|
pedroathome
915 posts
|
" said:
7 and 8 rather - Typo Log in to reply |
| A couple of Derby based queries 30/03/2015 at 19:08 #70548 | |
|
pedroathome
915 posts
|
Just got another 5 - Derby Dn Goods: With 2 trains in the Dn Goods line, bringing one across onto the Up Connect, The TD nearest to Signal 448 steps up to the berth by Signal 425, however, as soon as Track 709 the TD by Signal 458 then over writes the previously moved TD at Signal 425. This then leaves no headode on the Down Goods line. Log in to reply |
| A couple of Derby based queries 31/03/2015 at 11:49 #70567 | |
|
Stephen Fulcher
2078 posts
|
Mantis 12703.
Log in to reply |
| A couple of Derby based queries 01/04/2015 at 00:01 #70602 | |
|
pedroathome
915 posts
|
6 - Derby to Signal 434: I am unable to set a route from Platform 2 using Signal 442 through to Signal 434 using the Via 2 Via button. Just quering if this should be a route given that either way works from Platform 3. In addition here, if I have the route set from Signal 442 through to Signal 388, using the Via 1 control, I am then unable to set from signal 441 to signal 434 as route signal 442 to signal 388 is requiring points 720 reverse Log in to reply |
| A couple of Derby based queries 05/04/2015 at 13:49 #70799 | |
|
Hpotter
205 posts |
Above issues sorted for next update.
Log in to reply |