Page 1 of 1
Annbank Points Set Wrong 05/10/2016 at 18:25 #85630 | |
Gwasanaethau
![]() 509 posts |
Hi all, I am playing the fantastic 2015 timetable using the modern era layout. I currently have a train (4S28) that has entered at Mauchline and is trundling towards Newton-on-Ayr. It has stopped, however, at Annbank complaining that the “Points are set wrong”. My only options are to tell the driver to reverse, or to get them to wait 2/5/15 minutes before phoning back. Any thoughts on what to do to proceed from here? Loader version: 4.5.12 Sim data version: 4.5 Thanks Mark (Gwasanaethau) Post has attachments. Log in to view them. Last edited: 05/10/2016 at 18:34 by Gwasanaethau Reason: Save attached. Log in to reply |
Annbank Points Set Wrong 05/10/2016 at 19:44 #85636 | |
tynie123
![]() 234 posts |
Gwasanaethau in post 85630 said:Hi all, Log in to reply |
Annbank Points Set Wrong 05/10/2016 at 20:58 #85639 | |
Peter Bennet
![]() 5376 posts ![]() |
Points are hidden, though you can use f11 and look for PANN. However, the more curious question is why were they wrongly set. While it is possible to move (via f11) the points after the train has entered at Mauchline clearing SMA31 follows (in logical order in the same command) the setting of PANN and PMA32 to the right position. The logic is that if a train is detected as sitting at SMA31 and the necessary conditions (line clear, token is correct etc) to allow the train to proceed have been met the points will be moved to the correct position and the signal cleared. So its a bit of a mystery. Did a train enter or try to enter at Killoch? Peter I identify as half man half biscuit - crumbs! Log in to reply The following user said thank you: Gwasanaethau |
Annbank Points Set Wrong 06/10/2016 at 12:24 #85649 | |
Gwasanaethau
![]() 509 posts |
Peter Bennet in post 85639 said:Points are hidden, though you can use f11 and look for PANN. However, the more curious question is why were they wrongly set. While it is possible to move (via f11) the points after the train has entered at Mauchline clearing SMA31 follows (in logical order in the same command) the setting of PANN and PMA32 to the right position.The previous movement on that line was a train towards Killoch (I can’t remember the TD I’m afraid). If I recall correctly, I received the phonecall for 4S28 to enter as the previous train was still trundling towards Killoch, but it was a good while before 4S28 actually entered (at least 15 minutes). I wish I had a save from before all this occurred to send to you, but, alas, the previous save is a good two hours or more prior to this occurrance. Log in to reply |
Annbank Points Set Wrong 07/10/2016 at 20:21 #86669 | |
BarryM
![]() 2158 posts |
Gwasanaethau in post 85649 said:Peter Bennet in post 85639 said:Setting PANN points to normal allows the train to enter the sim.Points are hidden, though you can use f11 and look for PANN. However, the more curious question is why were they wrongly set. While it is possible to move (via f11) the points after the train has entered at Mauchline clearing SMA31 follows (in logical order in the same command) the setting of PANN and PMA32 to the right position.The previous movement on that line was a train towards Killoch (I can’t remember the TD I’m afraid). If I recall correctly, I received the phonecall for 4S28 to enter as the previous train was still trundling towards Killoch, but it was a good while before 4S28 actually entered (at least 15 minutes). I wish I had a save from before all this occurred to send to you, but, alas, the previous save is a good two hours or more prior to this occurrance. Could you provide a copy of the save prior to the incident? Barry Barry, Sydney, New South Wales, Australia Last edited: 07/10/2016 at 20:45 by BarryM Reason: add Log in to reply |
Annbank Points Set Wrong 08/10/2016 at 10:56 #86675 | |
Gwasanaethau
![]() 509 posts |
BarryM in post 86669 said:…No problem, Barry. Save is attached. This is almost three hours before the incident, just so you’re aware. G’luck! Mark (Gwasanaethau) Post has attachments. Log in to view them. Log in to reply |