Page 1 of 1
| New Version Incident control panel 19/09/2011 at 10:28 #21087 | |
Didcot
41 posts |
In version 2.227 of Westbury (and Exeter) in the incident control panel there is a Points table showing point numbers and facility to highlight point Numbers and tick normal and reverse detection Availability. Is there a way to find the layout location of these points. Also can somebody tell me how is this facility used . It is not mentioned in the Manual. Thanks Pete Log in to reply |
| Re: New Version Incident control panel 19/09/2011 at 10:32 #21088 | |
Peter Bennet
5402 posts |
There should be a button with a mouse on it, click that then the relevant point/signal/tc/whatever that you are interested in and the selected item should be highlighted. You can then fail (or whatever other options are available) that item. It's a generic thing so any instructions should go in the general manual not the Sim specific one. Peter I identify as half man half biscuit - crumbs! Last edited: 19/09/2011 at 11:56 by Peter Bennet Log in to reply |
| Re: New Version Incident control panel 19/09/2011 at 10:49 #21089 | |
|
Didcot
41 posts |
Thanks Peter for the very fast reply.! Is there a way of knowing these point numbers in relation to their position in the Sim Thanks Pete Log in to reply |
| Re: New Version Incident control panel 19/09/2011 at 11:31 #21090 | |
|
Peter Bennet
5402 posts |
By the method I explained- I can't think of a scenario where you'd need to know the number before you did the thing with the mouse to find it. If say you want to select point 1234A then where it is is irelevant but will become obvious when it fails. If you want to select the point entering Plat 2 at Swindon then you use the "find by mouse" that I explained. If you just want a general map for interest then someone will have to make it up and publish, as has been done on other Sims. Peter I identify as half man half biscuit - crumbs! Last edited: 19/09/2011 at 11:57 by Peter Bennet Log in to reply The following user said thank you: Didcot |
| Re: New Version Incident control panel 20/09/2011 at 19:08 #21141 | |
Steamer
3984 posts 
|
I did try to start a point diagram for brighton, with a view to making them for all sims eventually, however since crowded locations and points go hand-in-hand, it became very messy, especially since they are routinely 6 characters long. On this topic, what do the different isolation abbreviations mean (ENG, TI, BET), and why are some combined? "Don't stress/ relax/ let life roll off your backs./ Except for death and paying taxes/ everything in life.../ is only for now." (Avenue Q) Log in to reply |
| Re: New Version Incident control panel 20/09/2011 at 19:26 #21145 | |
headshot119
4869 posts |
" said:I did try to start a point diagram for brighton, with a view to making them for all sims eventually, however since crowded locations and points go hand-in-hand, it became very messy, especially since they are routinely 6 characters long.Isolations : ENG = Engineering, some form of possession T3, T2, T12 ect. (T codes are different types of possessions) TI = Traction Isolation. Perhaps the OHLE or third rail is not on. BET = Blocked to Electric Traction. The power isn't on. (Note in most real signal-boxes this is known as BTET) "Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Log in to reply The following user said thank you: Steamer |
| Re: New Version Incident control panel 26/09/2011 at 13:10 #21314 | |
jc92
3685 posts |
can anyone list the different possession types?
"We don't stop camborne wednesdays" Log in to reply |
| Re: New Version Incident control panel 26/09/2011 at 17:16 #21342 | |
|
y10g9
895 posts |
JC, isn't that what karl has done in the post above yours?
Log in to reply |