Page 1 of 1
NE Scotland Absolute Block Question 08/12/2012 at 11:41 #38891 | |
JohnMiller
![]() 321 posts |
Please find attached a sequence of Absolute Block bell codes between boxes that seem to fail ... it does this on all boxes
Post has attachments. Log in to view them. Log in to reply |
NE Scotland Absolute Block Question 08/12/2012 at 13:36 #38895 | |
NCC1701
![]() 129 posts |
Looks like you found the Welwyn release by accident...
Signalman Exeter West & Llangollen Log in to reply |
NE Scotland Absolute Block Question 08/12/2012 at 13:59 #38902 | |
northroad
![]() 872 posts |
I have found the same also. What I have done to reinstate the full red light that indicates (train on line) is to just right click once on the box that accepts the tol and that puts the red light back to the block. When I first encountered this I did notice that you got penalties for not putting train on line, however when I reinstate as I have described above there is no penalty. Geoff Last edited: 08/12/2012 at 13:59 by northroad Log in to reply |
NE Scotland Absolute Block Question 08/12/2012 at 21:56 #38935 | |
jc92
![]() 3649 posts ![]() |
just my own question to add (I have looked at the manual for guidance first!) when i offer a train from box A to box B and box B accepts, i get a green button as per the manual. however as soon as i pull off the section signal, the button at box B begins to flash. I have not sent TES so have not prompted any such action. is this standard sim behaviour or am I making some sort of glaring error? the manual makes no reference to the flashing green display on the block. "We don't stop camborne wednesdays" Log in to reply |
NE Scotland Absolute Block Question 08/12/2012 at 22:36 #38939 | |
Peter Bennet
![]() 5377 posts |
It's such a long time since I wrote the code for that. It was a bit of a nightmare to get to work and nearly got pulled at one point. For some reason however, it seems to be flashing on green after the 10 seconds and if I can't figure it out I'll remove it. However, it can only go to open circle if it's flashing (there is no other state that will allow it) so what you've captured must be a mid flash. The flashing is just so the receiving box (in m/Play) can see for 10 seconds after the ding - which bell it was if he controls more than one box. If it's flashing at the wrong time it can see it can be confusing. It's supposed to be a bit of fun so don't take it too seriously. Peter. I identify as half man half biscuit - crumbs! Log in to reply |
NE Scotland Absolute Block Question 08/12/2012 at 22:39 #38941 | |
jc92
![]() 3649 posts ![]() |
" said:Not at all peter, trains were running smoothly, i just wanted to make sure i was going about it the right way. I do quite like the way AB has been done. "We don't stop camborne wednesdays" Log in to reply |
NE Scotland Absolute Block Question 08/12/2012 at 22:43 #38942 | |
Peter Bennet
![]() 5377 posts |
On the specific question from the pictures I can't reproduce the reversion from R to W state in the last picture. What were the circumstances? Peter I identify as half man half biscuit - crumbs! Log in to reply |
NE Scotland Absolute Block Question 09/12/2012 at 23:01 #39013 | |
Peter Bennet
![]() 5377 posts |
Got it quite simple in the end. Peter I identify as half man half biscuit - crumbs! Log in to reply |
NE Scotland Absolute Block Question 10/12/2012 at 05:41 #39016 | |
JohnMiller
![]() 321 posts |
It just changes of its own accord, I have done some testing with the double click speed of the mouse but it still changes to white .. its as though one should right click 3 times & not two .. bit like 2 > 1 (out of section) John Log in to reply |
NE Scotland Absolute Block Question 10/12/2012 at 06:41 #39017 | |
Peter Bennet
![]() 5377 posts |
There are three basic operational states (G/W/R) but each state has a steady or flashing representation. So whether white solid or white flashing it's the same operational State, just represented differently. The flashing is just to represent the resonating of the bell, if you will. What was wrong was that when the flashing timer stopped then instructions to switch to the relevant solid state were flawed. Peter I identify as half man half biscuit - crumbs! Log in to reply The following user said thank you: JohnMiller |