Page 1 of 1
| Incident Control Panel (ICP) 29/06/2022 at 04:41 #147022 | |
Neal
10 posts |
I've accidentally discovered that I can use the ICP to highlight & clear Signal Failures, Track Section Failures, Points Failures etc. The Technician will still call some time later and report the fault fixed, but I'm wondering if this 'ability' is an available course of action to signalmen IRL, or whether it's the SimSig version of the 'Hand of God' . . . ? Log in to reply |
| Incident Control Panel (ICP) 29/06/2022 at 06:40 #147023 | |
flabberdacks
636 posts |
Just want to confirm that you're asking if a real life signaller can click a button that immediately fixes any failure?
Log in to reply |
| Incident Control Panel (ICP) 29/06/2022 at 06:42 #147024 | |
kaiwhara
587 posts |
flabberdacks in post 147023 said:Just want to confirm that you're asking if a real life signaller can click a button that immediately fixes any failure?Have I been missing that button at work all this time??!!!!!! Sorry guys, I am in the business of making people wait! Log in to reply |
| Incident Control Panel (ICP) 29/06/2022 at 07:07 #147025 | |
|
JamesN
1607 posts |
Generally it is SimSig’s “hand of god” yes; however there are some real-life installations where under certain circumstances the signaller can reset axle counters for example - which would be equivalent of going into ICP and clearing a track section failure. Similarly hand-cranking points could be done whenever provided there’s someone on the ground to do it.
Log in to reply The following user said thank you: Neal |
| Incident Control Panel (ICP) 29/06/2022 at 10:33 #147029 | |
|
TUT
532 posts |
JamesN in post 147025 said:Generally it is SimSig’s “hand of god” yes; however there are some real-life installations where under certain circumstances the signaller can reset axle counters for example - which would be equivalent of going into ICP and clearing a track section failure. Similarly hand-cranking points could be done whenever provided there’s someone on the ground to do it.Yeah, erm, you can attempt to reset an axle counter once, yes (you can attempt a second reset after it's been examined I think). It doesn't always work, but if it does you'll still have aspect restriction so not quite a magic mouse click to make the bad thing go away. Yes provided there's someone on the ground to hand crank the points, you can go through a form and a procedure yes. But that's quite a big 'provided'. Although, you can deal with the failure yourself while you wait for the technician/PO/RSA to arrive if you're competent to do so. Couldn't do that at an IECC though. Log in to reply |
| Incident Control Panel (ICP) 29/06/2022 at 17:18 #147036 | |
|
Sam Tugwell
494 posts |
TUT in post 147029 said:Yeah, erm, you can attempt to reset an axle counter once, yes (you can attempt a second reset after it's been examined I think).2 goes at resetting in 24 hours. After that S&T have to attend before a 3rd reset is attempted. "Signalman Exeter" Log in to reply |
| Incident Control Panel (ICP) 29/06/2022 at 17:39 #147038 | |
Steamer
3984 posts |
One feature not mentioned yet is the function to add isolations to track circuits for possessions etc, which would be used pretty regularly. Other than that and the unoccupy track sections/point winding discussed above, everything else is 'hand of god'. "Don't stress/ relax/ let life roll off your backs./ Except for death and paying taxes/ everything in life.../ is only for now." (Avenue Q) Log in to reply The following user said thank you: Neal |
| Incident Control Panel (ICP) 29/06/2022 at 21:23 #147040 | |
|
Stephen Fulcher
2078 posts |
You can use it to simulate a release of controls quite effectively. This is where a Technician can, under tightly defined circumstances, clear track circuits to move points or clear route locking. Log in to reply |
| Incident Control Panel (ICP) 29/06/2022 at 21:26 #147041 | |
|
Stephen Fulcher
2078 posts |
Sam Tugwell in post 147036 said:TUT in post 147029 said:The second go after it’s been examined is largely because they won’t reset unless the last count for a particular section is out, so the examining train “sweeps” the section and sets the last count to out.Yeah, erm, you can attempt to reset an axle counter once, yes (you can attempt a second reset after it's been examined I think).2 goes at resetting in 24 hours. After that S&T have to attend before a 3rd reset is attempted. Log in to reply |
| Incident Control Panel (ICP) 30/06/2022 at 00:43 #147043 | |
|
Sparky
84 posts |
Being able to reset axle counters is dependant on how it failed in the 1st place. If it failed due to a miscount i.e counting more axles in than out or vice versa then no a cooperative reset is required. If it is a count in fault then it is also a cooperative reset. A count out failure can be reset without field intervention. I intend to live forever. So far so good Log in to reply |
| Incident Control Panel (ICP) 30/06/2022 at 06:04 #147044 | |
|
Neal
10 posts |
Yeah, that's pretty much it.
Log in to reply |
| Incident Control Panel (ICP) 30/06/2022 at 10:25 #147045 | |
|
Keith Palmer
12 posts |
If only this could happen in a real scenario where a signaller could press a button and the failure self restores it self? Unfortunately, NO! On Britain's railways, any failure that occurs, signallers are at the mercy of the S&T arriving on site, and depending what the fault is, either points, track circuit failures, level crossing equipment, etc, etc, could in some cases, take hours to fix! So it's just a SimSig 'get out of jail card' to enable you to continue with the simulation without having to start all over again! Log in to reply |
| Incident Control Panel (ICP) 30/06/2022 at 21:00 #147065 | |
|
bill_gensheet
1413 posts |
However would not real-life S&T prioritise a fault blocking say half of Edinburgh Waverley over a lamp out on the Alloa branch ? For a start their van / tea urn is nearer Waverley. SimSig virtual technicians are simply timers. As such some use of 'get out of jail' could be justified. Bill Log in to reply |
| Incident Control Panel (ICP) 30/06/2022 at 21:34 #147066 | |
|
TUT
532 posts |
bill_gensheet in post 147065 said:However would not real-life S&T prioritise a fault blocking say half of Edinburgh Waverley over a lamp out on the Alloa branch ?Yeah but things often take quite a long time in real life. First you have to get to site through any traffic there might be, then fault tracing can take ages, then you find out what the problem is and you haven't got one in the van so you've got to go back to the depot. I think our S&T are magicians, but things can still take time. Then again I've had some really smart response times for fairly minor problems. But then who wouldn't wanna come out and see me, so I do understand 
Log in to reply |
| Incident Control Panel (ICP) 01/07/2022 at 16:14 #147092 | |
|
Stephen Fulcher
2078 posts |
We don’t drink much tea any more Bill, usually a latte from the nearest branch of a popular fast food chain. On a more serious note something locking up Waverley would certainly take precedence over a lamp out at Alloa, but as SimSig is a signalling simulation not a Route Control simulation it’s not worth losing too much sleep if the virtual technician would rather change the lamp first. Log in to reply |
| Incident Control Panel (ICP) 05/07/2022 at 10:15 #147150 | |
|
kbarber
1742 posts |
Of course, for those sims where a lever frame is being simulated and mechanical points still exist, there is a 'foot of God' for points failures: the bobby goes down the box stairs and applies their size 9 to the offending points. I won't say it never fails (I recall an occasion at Kensington North Main when we concluded a small grain of gravel had got into an FPL and it took a hammer to get things going, but the principle was the same) but it usually did the trick. There were also sealed releases for track circuits, which allowed you to release the lock on a points (or FPL) lever and keep traffic moving until the S&T arrived. With a suitable entry in the book, of course, and for failures only - strictly not for use if you'd boxed yourself up by your own stupidity.
Log in to reply |
| Incident Control Panel (ICP) 08/07/2022 at 09:50 #147187 | |
Giantray
347 posts |
Some Workstations now have TREL & PREL facilities that allow a Signaller to carry a procedure that in many locations is only available by getting an S&T Tech to release controls.
Professionalism mean nothing around a bunch of Amateur wannabees! Log in to reply |