Page 1 of 1
0M34 problem and subsequent route setting issues 16/02/2012 at 19:15 #29594 | |
RobS
![]() 6 posts |
I've run into a problem with routing trains in and out of platforms at Euston. It started when I struggled to route light engine 0M34 from platform 7 to the Down Carriage Shed via the Down Carriage Shed shunt neck. I assumed the route should be via BOR 1 or 2, but although this should be a valid route, using DEG route selectors, I could not set a route; always getting the message "Point(s) locked normal by another route", even though no other trains were in the vicinity nor other routes set. Rightly or wrongly, I changed some points manually by clicking on them, and eventually I managed to set a route. However since then, virtually every route I have tried to set into and out of Euston's platforms have failed, unless I set some of the points manually. It all worked perfectly up to then... Can anyone shed light on: 1) How I should have got 0M34 to the Down C.S. Shunt Neck 2) How I can "reset" things so that the routing works OK? Many thanks! Rob Log in to reply |
Re: 0M34 problem and subsequent route setting issues 16/02/2012 at 19:25 #29596 | |
derbybest
![]() 274 posts |
I just tried that route and it works for me
Log in to reply |
Re: 0M34 problem and subsequent route setting issues 16/02/2012 at 20:11 #29603 | |
clive
![]() 2766 posts |
Can you send me a saved game, please?
Log in to reply |
Re: 0M34 problem and subsequent route setting issues 16/02/2012 at 20:37 #29604 | |
RobS
![]() 6 posts |
" said:Can you send me a saved game, please?Hi Clive, Thanks for your interest. I've attached a saved game, just overlook the piled up trains - it only got this bad once the routing problem started ![]() Thanks, Rob Post has attachments. Log in to view them. Last edited: 16/02/2012 at 20:37 by RobS Reason: spelling error Log in to reply |
Re: 0M34 problem and subsequent route setting issues 17/02/2012 at 19:08 #29639 | |
RobS
![]() 6 posts |
" said:I just tried that route and it works for meHi Derbybest, Can I just clarify I'm "clicking the right buttons"? I click 7, D, E, G then 61. Is this what you did? Thanks, Rob Log in to reply |
Re: 0M34 problem and subsequent route setting issues 17/02/2012 at 19:37 #29640 | |
tlib
![]() 9 posts |
Hi Rob, In your save file you have a load of points locked (blue points) if you left click the points and clear the blue then you can route as normal. Tlib Log in to reply |
Re: 0M34 problem and subsequent route setting issues 17/02/2012 at 20:35 #29641 | |
RobS
![]() 6 posts |
" said:Hi Rob,Thanks Tlib, I'll give that a go. Still not sure why 0M34 wouldn't route from P7 to BOR1 or 2; I've gone back and still can't see any locked points at that stage; I think I've inadvertantly locked them in my attempt to set a route for 0M34 then compounded the problem thereafter... Cheers, Rob Log in to reply |
Re: 0M34 problem and subsequent route setting issues 17/02/2012 at 20:49 #29642 | |
RobS
![]() 6 posts |
" said:" said:Hi Rob,Thanks Tlib, I'll give that a go. Cancel that; just looked closer and one set was locked, preventing the route from P7 to BOR from setting. All now fine. Thanks to all for help and advice. Rob Log in to reply |