Page 1 of 1
| RTT & Letchworth CS 06/04/2014 at 17:01 #58496 | |
DaveHarries
1285 posts |
Hi all, I am currently working on a timetable for Kings Cross (Loader version) which will use the modern layout with 8 platforms at Finsbury Park. However I have a query regarding train entry times at Letchworth CS. A look at realtimetrains.co.uk (RTT) gives the following timing points for trains leaving Letchworth CS on the day I am working on: - Letchworth C.S.D - Letchworth CS Reception - Letchworth A/d line There are waiting times at Letchworth CS reception and there is no Letchworth A/d line shown on the sim. What would be the best timing to use as the entry point? I guess the departure time from the Letchworth A/d line but no harm in checking as I don't want to have bugs that I can't correct once the data has vanished (although that will be a while yet). Cheers, Dave Log in to reply |
| RTT & Letchworth CS 06/04/2014 at 19:15 #58505 | |
Steamer
3984 posts |
According to Quail, the Reception is the simulation's north exit, and the A/D line is the south exit. The layout is slightly different to the simulation though- according to Quail, there's no turnback siding, but instead two A/D roads at the south end of the sidings. The CSD itself is a fan of tracks, which converge near the northern exit. Google Map, with (hopefully) the A/D roads and Reception marked. "Don't stress/ relax/ let life roll off your backs./ Except for death and paying taxes/ everything in life.../ is only for now." (Avenue Q) Log in to reply The following user said thank you: DaveHarries |
| RTT & Letchworth CS 06/04/2014 at 20:34 #58506 | |
|
DaveHarries
1285 posts |
Steamer, Thanks for that. I think I will use the departure from the arr / dep line as the entry point. Could be the best way of doing things. Dave Log in to reply |
| RTT & Letchworth CS 06/04/2014 at 20:39 #58507 | |
dwelham313
139 posts |
Use the time from the A/D line. It should be approx 2 minutes from the train entering to the arrival time at Letchworth station. For some reason the sim is different to the real life set-up. Trains for the south exit the CS onto the reception line (up to K951 at the north end) and the driver changes ends. The shunter pulls hand points and authorises the driver past a stop board. The train then stops at another stop board and the driver will contact the signaller. The sig will tell the driver either A/D line (K240 - south exit on the sim) or south reception (K238 - rev sdg on the sim). The driver then sets hand points accordingly and will draw up to the signal. RTT shows the timing point as A/D line but trains can use either A/D or south reception to enter/exit the CS, via the north reception, depending on whichever line is free. Last edited: 06/04/2014 at 20:49 by dwelham313 Log in to reply |
| RTT & Letchworth CS 06/04/2014 at 21:38 #58509 | |
|
Danny252
1461 posts |
" said:Use the time from the A/D line. It should be approx 2 minutes from the train entering to the arrival time at Letchworth station. For some reason the sim is different to the real life set-up.That all sounds quite similar to how Simsig does it, apart from having two outbound lines - its just that the whole reversal part takes place before the train "enters" the sim! Looking at historical imagery, it seems that the South Rec/Turnback Siding may have been single-ended until a few years ago, although the quality makes it quite hard to tell for sure. Log in to reply |
| RTT & Letchworth CS 07/04/2014 at 04:20 #58513 | |
BarryM
2158 posts |
" said:" said:How old are these maps? It does not show the new flyover from Hitchin.Use the time from the A/D line. It should be approx 2 minutes from the train entering to the arrival time at Letchworth station. For some reason the sim is different to the real life set-up.That all sounds quite similar to how Simsig does it, apart from having two outbound lines - its just that the whole reversal part takes place before the train "enters" the sim! Looking at historical imagery, it seems that the South Rec/Turnback Siding may have been single-ended until a few years ago, although the quality makes it quite hard to tell for sure. Barry Barry, Sydney, New South Wales, Australia Log in to reply |
| RTT & Letchworth CS 07/04/2014 at 05:09 #58514 | |
|
dwelham313
139 posts |
There is one north-facing siding still in situ alongside the south reception albeit with no connection. I believe there were some layout changes when the carriage sidings were electrified. There is evidence of several more sidings which are long gone after the demise of the domestic coal workings to Letchworth.
Log in to reply |
| RTT & Letchworth CS 07/04/2014 at 14:25 #58521 | |
|
Danny252
1461 posts |
" said:" said:True, if the flyover is in Simsig, then any remodelled layout for Letchworth ought to be as well (assuming there was any change at all)." said:How old are these maps? It does not show the new flyover from Hitchin.Use the time from the A/D line. It should be approx 2 minutes from the train entering to the arrival time at Letchworth station. For some reason the sim is different to the real life set-up.That all sounds quite similar to how Simsig does it, apart from having two outbound lines - its just that the whole reversal part takes place before the train "enters" the sim! Looking at historical imagery, it seems that the South Rec/Turnback Siding may have been single-ended until a few years ago, although the quality makes it quite hard to tell for sure. Log in to reply |