Page 4 of 5
| York North/South 24/05/2016 at 17:00 #82618 | |
GeoffM
6376 posts |
#15360, thanks. That must have been in there for quite a while with nobody spotting (or reporting) it!
SimSig Boss Log in to reply |
| York North/South 24/05/2016 at 19:51 #82624 | |
Essexgirl
42 posts |
The first train from Darlington even now has a 15 ENG allowance built in between Darlington and Northallerton, this is to allow for slower running should the train run 'wrong road' under SIMBIDS.
Log in to reply The following user said thank you: officer dibble |
| York North/South 24/05/2016 at 20:12 #82627 | |
|
Essexgirl
42 posts |
" said:I noticed on viewing a very recent video of York Station in Youtube that platform 5 is actually split into 5a and 5b. This simulation seems to make no mention of this.The platform 5A/5B was an operational change not a signalling change. This was done so that TPE train stop on 5B and thus passengers know where to stand with a 3 car train stopping on the long platform, it was sometimes a bit hit and miss, especially with passengers who didnt know the unmarked stopping point. Also all the 'long distance' trains now stop on 5A, this enables the VTEC trains to stop lined up with their 'stopping' trains in P6. As far as the display in the IECC there is only a P5. Log in to reply The following user said thank you: officer dibble |
| York North/South 24/05/2016 at 20:30 #82630 | |
|
Essexgirl
42 posts |
" said:Springwell Lane telephones go to Low Gates which is presumably why it's slotted.Geoff, You are correct about the telephones/slots. Low Gates is effectively a crossing box to us, and as they are in control of the crossing (telephones) the signals are slotted so they can put back the signals if required in an emergency. In reality the slot are always given so that as soon as we in York set the route, the signals clear. Had a look at this at work tonight (LOS at Low Gates), and tried it out. York set the route Y701GPL to Y500LOS, which is repeated on the diagram in Low Gates Box, the route sets (signal stays red), Low Gates drops the barriers and when able gives slot LG5 for signal Y701GPL, which then clears. Hope this helps everyone Last edited: 24/05/2016 at 21:02 by Essexgirl Log in to reply The following users said thank you: officer dibble, sunocske, JamesN, GeoffM |
| York North/South 25/05/2016 at 08:56 #82647 | |
KymriskaDraken
963 posts |
" said:The first train from Darlington even now has a 15 ENG allowance built in between Darlington and Northallerton, this is to allow for slower running should the train run 'wrong road' under SIMBIDS.Oh, how I used to hate CANBIDS when I worked in Bristol. Kev Log in to reply |
| York North/South 26/05/2016 at 12:12 #82676 | |
|
Ray
211 posts |
I am on the 15th Oct 1009 timetable at 1855 hours. The trains 6H89 and 4D74 both arrive at Gasgoigne Wood West around the same time. The locomotives require to perform a run round but after the movement the locomotives will not join. Its funny that some timetables and sims manage to work joins well such as Motherwell and Carlisle with no difficulty and then we have a new sim which does not.
Log in to reply |
| York North/South 26/05/2016 at 15:30 #82681 | |
DriverCurran
688 posts |
Tongue firmly in cheek here, but I wouldn't have expected any trains to run on the 15th October 1009. I will at this point get my coat and shout taxiiiiiii  Paul You have to get a red before you can get any other colour Log in to reply |
| York North/South 26/05/2016 at 16:12 #82682 | |
|
JamesN
1607 posts 
|
" said:I am on the 15th Oct 1009 timetable at 1855 hours. The trains 6H89 and 4D74 both arrive at Gasgoigne Wood West around the same time. The locomotives require to perform a run round but after the movement the locomotives will not join. Its funny that some timetables and sims manage to work joins well such as Motherwell and Carlisle with no difficulty and then we have a new sim which does not.Ok so why won't they join? What is the status of the light engines under F2 (Stopped at xxxxxx, train yyyy in front, etc)? If you click on a berth, or sticky note with the light engine's Train ID, what location is at the top of the list? Log in to reply |
| York North/South 26/05/2016 at 16:44 #82683 | |
jc92
3685 posts
|
" said:" said:http://www.SimSig.co.uk/dokuwiki/doku.php?id=simulations:yorkns:gascoigne_woodI am on the 15th Oct 1009 timetable at 1855 hours. The trains 6H89 and 4D74 both arrive at Gasgoigne Wood West around the same time. The locomotives require to perform a run round but after the movement the locomotives will not join. Its funny that some timetables and sims manage to work joins well such as Motherwell and Carlisle with no difficulty and then we have a new sim which does not.Ok so why won't they join? What is the status of the light engines under F2 (Stopped at xxxxxx, train yyyy in front, etc)? If you click on a berth, or sticky note with the light engine's Train ID, what location is at the top of the list? The manual covers this issue and confirms a core code update is en route. "We don't stop camborne wednesdays" Log in to reply |
| York North/South 26/05/2016 at 16:59 #82685 | |
|
Ray
211 posts |
Thanks for replies. Yes the year 1009 is a bit early for trains ! The status of one of the locos was : train in front. I think the other train was held at a shunt signal which was at red. I tried to move this loco by authorising it to pass at red but that had no effect. Whilst I am writing this, I remember that some sims allow an easy edit of the timetable to the location at the join. The loco then recognises its "new" location and usually performs the join. Unfortunately there newer sims seem to have an in-built complication which prevents one from editing the location and the loco can never be stepped to its join location. Log in to reply |
| York North/South 30/05/2016 at 10:38 #82747 | |
ajax103
1120 posts |
Am enjoying York but who am I meant to call to ask for permission for trains approaching Y243 routed for York Yard North? I have checked the wiki and as below it doesn't actually say :doh York Yard North Permission is required to enter York Yard North from Y243/245/247 and Y262/312/666. The yard will phone you to inform of a departing train. When approaching Y243 to go into the yard, a train will come to a stand some tens of seconds before the position light aspect will light, allowing the train to proceed. It is not known why the approach control timeout is overly long. Other then that, so far it's been a good learning curve learning all the various routes 
Last edited: 30/05/2016 at 12:29 by ajax103 Log in to reply |
| York North/South 01/06/2016 at 12:10 #82826 | |
|
ajax103
1120 posts |
Can the player place blocks on the first controlled signal in the sim at places where trains enter ie Signal 735 has a Blok, would I be right in assuming all trains booked over that line would pass Signal 737 as the first controlled signal?
Log in to reply |
| York North/South 05/06/2016 at 17:49 #82914 | |
|
Jan
906 posts |
" said:The first train from Darlington even now has a 15 ENG allowance built in between Darlington and Northallerton, this is to allow for slower running should the train run 'wrong road' under SIMBIDS.Interestingly enough, the public timetable apparently has the allowance between Northallerton and York, so looking at RTT/OTT, that train usually seems to depart early (compared to the WTT) from Northallerton and put in an extended dwell at York instead. Two million people attempt to use Birmingham's magnificent rail network every year, with just over a million of them managing to get further than Smethwick. Log in to reply |
| York North/South 08/06/2016 at 02:38 #82938 | |
|
GeoffM
6376 posts |
York has now been updated to version 1.2. Issues fixed are listed here. The main issue of interest is the issue of trains running Gascoigne Wood<->Sherburn Jn<->Church Fenton<->Colton Jn which I believe should now be fixed.
SimSig Boss Log in to reply |
| York North/South 02/07/2016 at 06:42 #83333 | |
BarryM
2158 posts |
" said:[quote="Ray" post=82496]I noticed on viewing a very recent video of York Station in Youtube that platform 5 is actually split into 5a and 5b. This simulation seems to make no mention of this.Signal Y243 is the first signal on North's Panel Down Slow line and is the signal for entry into North Sidings. Barry[/quote Sorry, I interpret this message incorrectly. A telephone call to North Yard lists choice signal 248. This should be signal 243! Barry Barry, Sydney, New South Wales, Australia Log in to reply |
| York North/South 08/07/2016 at 15:55 #83467 | |
|
Slash
76 posts |
I've just started York and it's great. I've got all the ARS switched on in IECC mode at the moment, it's good for learning the sim. Thanks for another highly addictive and really well made product.
Log in to reply The following user said thank you: GeoffM |
| York North/South 08/07/2016 at 18:07 #83484 | |
|
GeoffM
6376 posts |
" said:A telephone call to North Yard lists choice signal 248. This should be signal 243!The logic is that you enter the yard via [the back of] signal 248. Otherwise the call would be from 635, 243, 245, and 247 which is a bit long. SimSig Boss Log in to reply The following user said thank you: BarryM |
| York North/South 24/07/2016 at 15:47 #83777 | |
|
pm77
3 posts |
" said:The route for 701-500 officially requires CH occ 120 sec. CF, CG clear OR CE occ, CF occ once 701( B ) cleared. 895 points locked and detected normal. Low Gates barriers down (at time of clearing) and crossing clear button operated. Lastly LG5 slot from Low gates LG5 no longer exists (apart from in the relay room at low gates, and the control tables), It's Y701 slot and it's shown as Y701 at Low Gates (although it is handwritten LG5 on the panel from when it was first commissioned to help avoid any confusion regarding old and new signal ID's) For reference LG1 = Y471 LG2 = Y480 LG3 = Y473 LG4 = Y696 LG5 = Y701 LG6 = Y702 LG7 = Y477 LG8 = Y484 Y482 is written as LG4 but I'd have to double check (I think it's LG9) Log in to reply The following user said thank you: GeoffM |
| York North/South 24/07/2016 at 23:50 #83784 | |
|
BarryM
2158 posts |
pm77 Welcome to Simsig! Barry Barry, Sydney, New South Wales, Australia Log in to reply The following user said thank you: pm77 |
| York North/South 25/07/2016 at 15:53 #83791 | |
|
GeoffM
6376 posts |
" said:The route for 701-500 officially requires CH occ 120 sec. CF, CG clear OR CE occ, CF occ once 701( B ) cleared. 895 points locked and detected normal. Low Gates barriers down (at time of clearing) and crossing clear button operated. Lastly LG5 slot from Low gatesAh, calling-on only, last wheel replacement. Thanks. Quote: For referenceI wonder whether the Low Gates to York interface simplifies it a bit. For example, LG4 is the slot for Y482, Y698, and Y696, only one of which can ever be set at a time. http://photos.signalling.org/picture?/12717/category/1224-2008 SimSig Boss Last edited: 25/07/2016 at 15:54 by GeoffM Log in to reply |
| York North/South 28/07/2016 at 20:10 #83832 | |
|
pm77
3 posts |
" said:Your photo is correct, all three signals share LG4 slot. The signals are all SSI controlled (as are all the York signals at Low Gates) and all in the same location case. They all have 2 routes, to Y480 and Y478. Only Y480 requires the slot. The slot request for LG4 is only on one input from Low Gates. Last edited: 28/07/2016 at 20:10 by pm77 Log in to reply |
| York North/South 10/09/2016 at 20:02 #84662 | |
|
tjfrancis
359 posts
|
i am speachless on this bug [attachment=3953]bugyorktrainjumpingtracks.pdf[/attachment] Post has attachments. Log in to view them. I am dyslexic so please consider this when reading my posts Log in to reply |
| York North/South 10/09/2016 at 20:04 #84663 | |
|
JamesN
1607 posts
|
" said:i am speachless on this bugOk, without the drama can you explain what's happening in the screenshot? Log in to reply The following user said thank you: DriverCurran |
| York North/South 10/09/2016 at 20:09 #84664 | |
|
MarkC
1105 posts |
" said:" said:from looking at the screen shot it looks like the train comming out of the sidings set up route but it highlighted the track circut though P10 at yorki am speachless on this bugOk, without the drama can you explain what's happening in the screenshot? Last edited: 10/09/2016 at 20:09 by MarkC Log in to reply |
| York North/South 10/09/2016 at 20:12 #84665 | |
headshot119
4869 posts |
" said:" said:Route 213AM is set but some of the ULCs aren't shown as locked, but 213 is showing a proceed aspect. (At least that's the only thing that I can see that is wrong)i am speachless on this bugOk, without the drama can you explain what's happening in the screenshot? " said: i am speachless on this bugYou are playing in the game currently being hosted (future readers note the hosting thread may have been destroyed), either your own connection to the server, or the hosts out bound connection doesn't have enough bandwith to cope with the session that is being hosted, and there is some severe delay between the host and the clients, or vice versa. Judging by the chatter in the shoutbox some very strange things are happening. Noting the bug you had in Kings Cross multiplayer yesterday hosted by a different person, I can only conclude there is an issue with the speed of your connection, I was only able to reproduce both bugs if I set up a connection between two machines and artificially throttle the speed. "Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Last edited: 10/09/2016 at 20:12 by headshot119 Log in to reply |