Page 1 of 1
| Springburn ARS 18/05/2010 at 16:37 #1276 | |
320322
86 posts |
Not sure if its been reported but the ARS for platform 3 at Springburn seems to be inoperative. I'm guessing someone knows.
Log in to reply |
| Springburn ARS 18/05/2010 at 16:37 #9274 | |
|
320322
86 posts |
Not sure if its been reported but the ARS for platform 3 at Springburn seems to be inoperative. I'm guessing someone knows.
Log in to reply |
| Springburn ARS 18/05/2010 at 17:36 #9275 | |
postal
5263 posts |
Works fine for me. Have you got the ACI turned on (or are you entering the new TDs manually) because the ARS works off the displayed headcode?
“In life, there is always someone out there, who won’t like you, for whatever reason, don’t let the insecurities in their lives affect yours.” – Rashida Rowe Log in to reply |
| Springburn ARS 18/05/2010 at 19:48 #9277 | |
Peter Bennet
5402 posts 
|
It's not true ARS so the TD is not important here- it's a very simple and crude system. Is it trains going into P3 or leaving? Trains arriving have their timetable analysed and the route to P3 or p4 is set according to what is read. When a TRTS is tripped that sets the route back out- I know there is an issue with TRTS but I can't remember if Springburn was affected or not- I assume from what John says that it must be OK. Peter I identify as half man half biscuit - crumbs! Log in to reply |
| Springburn ARS 18/05/2010 at 23:34 #9282 | |
|
320322
86 posts |
Its the trains from Milngavie that are not working with the ARS. I know the area well and I know its ARS for platforms 3 & 4 and Manual for Platform 1 & 2. Info from a local about Springburn. All platform starting signals are the standard 3 aspect. Platform 1 has a position 3 route indicator for the Cowlairs Chord , Platform 2 Has a position 3 route indicator for trains to Cumbernauld. Platform 1 also has a signal at the opposite end along with platform 2 for bi directional working. Platform 3 currently is for local electrics (I think signalled from the platform Starter at Barnhill signal CC324 , I could be wrong). Platform 4 is basically out of use but I've known that platform to stable DMU's in , obviously with the signalled move from platform 2 at barnhill (reversing). Hope this information is of use. Peter Bennet said: It's not true ARS so the TD is not important here- it's a very simple and crude system. Log in to reply |
| Springburn ARS 19/05/2010 at 05:44 #9284 | |
|
Peter Bennet
5402 posts
|
Thank you for the information; however as to the problem you have not answered the question- is it incoming or outgoing trains that you have the problem with? I read the original note as outgoing but the newer as it being the incoming- also I assume you are using one of the released timetables. Can you clarify exactly what the circumstances of the problem is. Peter I identify as half man half biscuit - crumbs! Log in to reply |
| Springburn ARS 19/05/2010 at 11:12 #9285 | |
|
320322
86 posts |
Both Directions. I basically have to manually set the route in advance on the train entering at Bellgrove Junction and setting the route back after the train from Milngavie has arrived.
Log in to reply |
| Springburn ARS 19/05/2010 at 12:25 #9287 | |
|
AndyG
1842 posts |
Are BOTH the ACI and ARS buttons enabled?
I can only help one person a day. Today's not your day. Tomorrow doesn't look too good either. Log in to reply |
| Springburn ARS 19/05/2010 at 13:22 #9288 | |
|
320322
86 posts |
Both buttons are on , yes. Changes the headcodes of the trains from Milngavie but doesn't set the route for them in either direction.
Log in to reply |
| Springburn ARS 19/05/2010 at 19:08 #9293 | |
|
Peter Bennet
5402 posts
|
Can you send me a save. Address under contact Us. Peter I identify as half man half biscuit - crumbs! Log in to reply |
| Springburn ARS 19/05/2010 at 21:19 #9294 | |
|
Adrian the Rock
111 posts |
Guys When I last played Central Scotland, the Springburn ARS worked for arrivals but not for departures. I'm 99.99% sure the latter is because the TRTS problem does affect Springburn. Well, I certainly never had the TRTS go off there when I was playing, and that was not always because I'd remembered to pull off in good time for the departures! Log in to reply |
| Springburn ARS 19/05/2010 at 21:46 #9295 | |
|
Peter Bennet
5402 posts
|
Just confirmed Springburn TRTS is on the known issues on WIKI. So that's half the conundrum resolved! Peter I identify as half man half biscuit - crumbs! Log in to reply |
| Springburn ARS 19/05/2010 at 23:23 #9297 | |
|
320322
86 posts |
TRTS wasn't an issue. It was the arrivals and departures that are causing problems. When I find how to locate the .SSG files in vista , I'll be happy to forward them to you Peter.
Log in to reply |
| Springburn ARS 20/05/2010 at 05:41 #9298 | |
|
Peter Bennet
5402 posts
|
TRTS is an issue because that drives the auto-working for departures: code says if TRTS Sig[P3] then call route from Sig[P3]-similar for P4 Just do a search for .ssg and you should pick it up that way. Peter I identify as half man half biscuit - crumbs! Log in to reply |
| Springburn ARS 21/05/2010 at 00:07 #9315 | |
|
320322
86 posts |
I'll look that up for the .ssg files. Its the case of finding them. Simsig knows where to look but I'm still looking into it. I shall forward the file with details of the era soon. Sorry for the delay (pardon the pun in a signalling simulator!)
Log in to reply |