Page 1 of 1
| 6E11 at grantshouse GF 23/02/2012 at 22:15 #29853 | |
jc92
3690 posts 
|
whilst playing the edinburgh 1993 timetable, i have train 6E11 at grantshouse loop, which has detached a (presumably) pilot loco which runs into the engineers sidings. however, depsite the fact no signals or overlaps conflict, the ground frame will not release and throws up the corresponding message in the message box can anyone enlighten me on the reason, if any that the groundframe will not release? joe "We don't stop camborne wednesdays" Log in to reply |
| Re: 6E11 at grantshouse GF 23/02/2012 at 22:26 #29855 | |
headshot119
4869 posts |
Is P6 the UP end loop exit point normalized? (Pressing the frame release doesn't do it automatically.)
"Passengers for New Lane, should be seated in the rear coach of the train " - Opinions are my own and not those of my employer Last edited: 23/02/2012 at 22:27 by headshot119 Log in to reply |
| Re: 6E11 at grantshouse GF 23/02/2012 at 22:28 #29856 | |
|
jc92
3690 posts
|
ive tried to normalise it, but it refuses to move over
"We don't stop camborne wednesdays" Log in to reply |
| Re: 6E11 at grantshouse GF 24/02/2012 at 01:57 #29867 | |
BarryM
2158 posts |
It works fine for me with track TGHLU occupied. Do you have any tracks occupied nearby? Barry Edit I ran a train into the loop and am unable to get a release for the GF. Barry, Sydney, New South Wales, Australia Last edited: 24/02/2012 at 02:21 by BarryM Log in to reply |
| Re: 6E11 at grantshouse GF 24/02/2012 at 02:05 #29868 | |
|
jc92
3690 posts
|
only the loop, im probably doing something blindingly obvious. i have the loop TC occupied, is there a timeout at all? as the direction arrow is still illuminated
"We don't stop camborne wednesdays" Last edited: 24/02/2012 at 02:06 by jc92 Log in to reply |
| Re: 6E11 at grantshouse GF 24/02/2012 at 02:33 #29869 | |
|
BarryM
2158 posts |
To release GF, the points in the loop need to be normalised! Did you see what happened to the assistant engine? Mine disappeared off F2!. Barry Barry, Sydney, New South Wales, Australia Log in to reply |
| Re: 6E11 at grantshouse GF 24/02/2012 at 02:37 #29870 | |
|
jc92
3690 posts
|
got it now... i was attempting to normalise the points points between the loop and engineers sidings, not the points on the mainline. it now works fine for me cheers. a minor bit of confusion on my part regards which points we were talking about. joe "We don't stop camborne wednesdays" Log in to reply |
| Re: 6E11 at grantshouse GF 24/02/2012 at 02:56 #29871 | |
|
BarryM
2158 posts |
" said:To release GF, the points in the loop need to be normalised! Did you see what happened to the assistant engine? Mine disappeared off F2!.Joe, What happened to 0E11? Barry Barry, Sydney, New South Wales, Australia Log in to reply |
| Re: 6E11 at grantshouse GF 24/02/2012 at 03:05 #29872 | |
|
jc92
3690 posts
|
i beleive it is made to disapear, then is ruled to reappear later under rules? i havent got that far yet
"We don't stop camborne wednesdays" Log in to reply |
| Re: 6E11 at grantshouse GF 24/02/2012 at 04:24 #29874 | |
|
BarryM
2158 posts |
Should show going to Engineer's Siding in F2? One for Peter? Barry Barry, Sydney, New South Wales, Australia Last edited: 24/02/2012 at 04:26 by BarryM Log in to reply |
| Re: 6E11 at grantshouse GF 24/02/2012 at 06:45 #29878 | |
Peter Bennet
5402 posts |
" said:Should show going to Engineer's Siding in F2?You've lost me- when a train enters the siding it'll fall off the Sim after 180m and then return later and an "entry". The only thing that I am aware of that was a problem in testing was where you forget to restore the EG438 (PL) the remaining of the train may follow! Though that may have been before we had "unpowered" states - can't remember the full details. Peter I identify as half man half biscuit - crumbs! Log in to reply |
| Re: 6E11 at grantshouse GF 24/02/2012 at 08:42 #29879 | |
|
BarryM
2158 posts |
" said:" said:When the assistant engine finishes dividing, F2 does not show the engine. It disappears without setting the GF.Should show going to Engineer's Siding in F2?You've lost me- when a train enters the siding it'll fall off the Sim after 180m and then return later and an "entry". The only thing that I am aware of that was a problem in testing was where you forget to restore the EG438 (PL) the remaining of the train may follow! Though that may have been before we had "unpowered" states - can't remember the full details. Barry Barry, Sydney, New South Wales, Australia Log in to reply |
| Re: 6E11 at grantshouse GF 29/02/2012 at 02:01 #30224 | |
bill_gensheet
1416 posts |
Just run through this bit on its' own a couple of times, and it all seems to work as expected. 0E11 goes into the engineers sidings and exits. 6E11-1 heads off at least 4 minutes later (the rule stops it following 0E11 giving you 4 minutes to put EG438 back), and normalise the GF for the train to depart. Then at 0710 0E11-1 enters, operate the GF again and it heads back to Edinburgh. If ignored long enough 0E11 phones up. All I can think is that as 0E11 only shows on F2 for a minute or so from dividing to exiting you missed it. Bill (1993 is my TT) Log in to reply |