Page 1 of 1
| Gloucester TT Help 19/10/2013 at 14:57 #50147 | |
DaveHarries
1287 posts |
Afternoon all, I am working on a WTT for the Gloucester derailment recently. I have a train that arrives Gloucester as 1V02 (0537 Birmingham New St - Gloucester) which I am putting into platform 2 at Gloucester. The next working from this platform is train 1L00 (0710 Gloucester - Stanstead Airport). At the same time it seems that, despite the derailment at the Lydney end of the station, RTT (Real Time Trains) says that train 1M00 worked through from Cardiff Central and into Platform 4: http://www.realtimetrains.co.uk/train/P30107/2013/10/17/advanced This suggests that 1M00 must have worked wrong line up from Lydney. Seeing as I can't program such a working (there are no crossovers) I intend to vary things slightly as follows: - run 1V02 as 2x 3-car Class 170 (instead of 1) - divide 1V02 at Gloucester with the rear (on arrival) portion departing again as 1L00 at 0710 - add a working at 0720 as 5M00 to put the remaining 170 from Platform 2 to Platform 4. The question is this. Am I better to let the proposed 5M00 work: a) into the UGL (or DGL) at Barnwood Junction, then back into Platform 4? or b) to G429 (at Horton Road LC) and then reverse into P4 from G446? Either route is possible but which would be best? I can't put the proposed 5M00 into P4 any earlier than 0715 due to another train, departing at 0715, using P4. And, due to closure of the lines immediately at the Lydney end of Gloucester station, I can't send 5M00 there. Advice welcome. Thanks, Dave Last edited: 19/10/2013 at 14:59 by DaveHarries Log in to reply |
| Gloucester TT Help 19/10/2013 at 16:15 #50150 | |
GW43125
495 posts |
" said:Afternoon all,I think that's up to you, but I would personally call it 5Z00 as it's not in the usual tt Log in to reply The following user said thank you: DaveHarries |
| Gloucester TT Help 20/10/2013 at 08:09 #50168 | |
|
derbybest
274 posts |
Having not looked into this the first thing that springs to mind is that 1M00 ran via Bristol Parkway instead of Severn Tunnel Jcn
Log in to reply |
| Gloucester TT Help 20/10/2013 at 13:30 #50179 | |
|
DaveHarries
1287 posts |
" said:I think that's up to you, but I would personally call it 5Z00 as it's not in the usual tt I hadn't thought of that. Thanks and I will. " said: Having not looked into this the first thing that springs to mind is that 1M00 ran via Bristol Parkway instead of Severn Tunnel Jcn Can't have done. There is a time given for a Lydney call. And even if the train had come via. BPW it would still have passed Severn Tunnel Junction. Cheers, Dave Log in to reply |
| Gloucester TT Help 20/10/2013 at 22:30 #50198 | |
|
valenta43002
43 posts |
1M00 did go via Bristol Parkway as did the last southbound one in the evening, 6b13 came that way before reversing on the avoiding line and back down to Westerleigh
Log in to reply |
| Gloucester TT Help 21/10/2013 at 11:51 #50209 | |
|
officer dibble
410 posts |
Dave, Just done a bit of digging at work & ran a replay for the morning of the 17th October...... 1V02 (formed 170398) formed 1L00 0710d , using platform 2 @ Gloucester. 1M00 (formed 170103) was diverted & arrived by way of Bristol Parkway & Charfield, reversing in platform 4 @ Gloucester. Hope this helps. Paul When in doubt - Contingency plan 2A. Someone didn't buy the milk - 2A. Someone sneezed at Swansea - 2A. A driver complains the cab is too cold - 2A. Unable to operate a HEx service 4 vice 8 - 2A. Points failure at Ipswich - 2A. Landslip at Pitlochry - 2A Last edited: 21/10/2013 at 11:52 by officer dibble Log in to reply The following users said thank you: Temple Meads, JamesN |